Its range through two rooms, up stairs and down a hall is very good. I've never once had a problem with dropped signals. I turn my laptop on and the signal stays solid until I turn it off. I'm using 128-bit WEP encryption, as well.

The speed is terrific. I applaud D-Link. I picked this combo because of the 22Mbps data rate. I can tell you that it really does double your throughput. On top of that, D-Link has a new firmware for the 900AP and driver for the 650+ that provided 4x/44Mbps mode. Note: it never actually negotiates at 44Mbps, but it does boost the speed. For example, at 2x/22Mbps, I get an average of 6.5Mbps (tested with QCheck from www.netiq.com), and at 4x/44Mbps, I get an average of 9.2Mbps... almost a 50% boost. Advertisement aside, getting 9Mbps from 802.11b is absolutely terrific.

Although I'm so high on this combo, if you're thinking of ordering any combo, I suggest going with D-Link's Extreme G 802.11g combo of DI-614 and DWL-G650, like I've done (should arrive in a few days).

The wireless network works now, but occasionally, a remote computer can't get through. Pinging the AP seems to remedy this. Other times (once every couple months), the unit stops working entirely. So I load up the configuration utility and play with the settings until it magically starts working again.

Its inconsistent behavior is extremely frustrating, and I'm tempted to throw it away and buy a different AP, just to get rid of the hassle. I don't recommend this product to anyone.

In addition, if you install the USB drivers for the access point on a computer, despite USB's hot-swap ability, make sure you reboot prior to trying to modify configurations.

But you can get mac address filtering to work. The file needs to be in a specific format. Each address must be on it's own line, and the last line in the file should be empty (i.e. hit Enter after you're done entering the last entry).

I've been updating the firmware and Windows software for the past week (bought it last week), and it seems like they put up a new version of the firmware every 2 days. This is probably a fair indicator that the device was released with immature software, and that they're struggling to get the thing to a point where it actually works for their customers.

I do not recommend this product to anyone.

#1 - Setup
The physical installation is a snap. Plug in the cables and you're done. Installing and configuring with the USB configuration program was easy. But then you have to switch to the SNMP configuration tool if you want to use any of the more useful features like MAC authentication. Only problem: you need to assign it an IP address, which is hard for those of us that use public IP addresses, since you either waste a public IP or set up a private IP on a different mask and alias the configuring computer's interface to communicate with the private netmask. It's manageable for someone that does networking for a living, but certainly not for a typical consumer.

#2 - Signal Strength and Latency
I don't think this is as strong as most AP's. I can AdHoc between two cards across my apartment complex, but I only get very weak intermittent signals using the AP from the same location. While playing games such as WarCraft 3 over the WLAN, I often times get timeouts and lag, for something that only averages 20ms in ping times even if the cards are in good range with 80-90% signal.

#3 - SNMP
For a product that claims to be SNMP manageable, it certainly isn't SNMP compliant. It uses its own proprietary SNMP OID's and can't be used with typical management programs. On the good side, there's a Perl filter online for those interested in running MRTG for bandwidth usage graphs over this AP. VERY useful.

Overall, I would recommend this AP as it is very cheap and still useful for all my needs.

The DWL-900 appears to do everything plus more than the DWL-1000 as far as I can tell, but I am very happy with both access points.

The included USB connection and cable made setup a snap. Only non-trivial issue was the need to use a cross-over cable (rather than a standard network cable) in my situation. If using two of these devices to connect two hubs, you would just use the uplink ports of each with standard cables.

PRO's: Low Price; Easy Setup; Configurable as either a Wireless Access Point or a Gateway (to bridge Wireless networks together); Detachable Antennae (can potentially connect aftermarket antennae to allow for greater coverage); Compatible with any Ethernet Router that has an extra ethernet port.

CON's: USB Connection Required for Setup (but drivers available for current OS's including XP)--afterwards can be managed via SNMP software included with the router; USB Cable Included, but, No Ethernet Cable Included.

NOTES: This product is only a Wireless Access Point -- It does not function as a ROUTER--so if you want/need to share a Cable Modem or other network connection wirelessly you'll need a separate router,...